Skip to main content

Water quality in pig production: Pay attention to these 5 indicators

March 22, 2017

Water is the most precious element on Earth. Access to clean water is fundamental for all living creatures, and for farm animals, the quality of the water they drink can have a direct impact on performance and productivity.

Like humans, most of the pig’s body is water, making up 82 percent of a young pig’s bodyweight and 55 percent of grown pig’s bodyweight (Kober, 1993).

In general, pigs tend to drink about 10 percent of their bodyweight per day or roughly two times the amount of feed they eat. Mortality, feed intake, growth rates and feed efficiency rates are known to be affected by the quality of the water provided (Stull et al., 1999).

Five points of water quality in pig production

In general, the quality of the pig’s water can be determined by measuring the presence of the following organic and inorganic elements:

1.Total bacterial count

Water contamination by bacteria is estimated by measuring the level of coliforms per milliliter of water. A total bacterial count of 50 colony forming units (cfu)/ml is considered good. If coliform levels are higher than 100 cfu/ml, then it is recommended to use a chlorine treatment.

When dealing with bacteria in the drinking water, it is important to consider the cleanliness of the water lines. Biofilm in pipes can be a considerable source of microorganisms in the water, but chlorine-based disinfectants have little to no effect on biofilms.  It’s important to flush out all buildup regularly.

2. pH

Water pH ranging from 5.5 to 8.5 is considered acceptable. If water is too acidic (lower than 5), it can create corrosion and damage pipes and waterlines; on the other hand, a basic pH (higher than 8.5) can leave scaly deposits.

3. Hardness

Calcium and magnesium are the two predominant minerals that make water “hard.” In pig production, hard water can contribute to the formation of scale deposits. The optimum water hardness in pig production is below 60 parts per million (ppm) of calcium carbonate (CaCO3).

4. Total dissolved solids

Total dissolved solids (TDS), also known as water salinity, is the amount of soluble salts and minerals dissolved in the water. Contaminants are usually measured in parts per million (ppm). The majority of the time, the amount of minerals or salts dissolved is well within the acceptable ranges, but sometimes very high levels can damage performance or equipment.

5. Nitrates and nitrites

Nitrates and nitrites are usually present in the water because the water supply is exposed to material with high nitrogen levels, such as animal waste, nitrogen fertilizers or decomposing organic material. Especially in monogastric animals, nitrites are 10 times more toxic than nitrates (Emerick, 1974). Levels as low as 0.10 mg/l of nitrite can impact performance in pigs.

There are various methods for treating water based on the type of issue as well as its severity:

Problem
Solution
Coliform count
Chlorinate water
Water hardness
Install a water softener
High nitrates or other minerals
Iron exchange or reverse osmosis treatment system
Iron
Filtration
High water pH
Acidification

Good water quality starts by implementing a program for testing as well as training farm personnel on spotting issues. It is recommended to test water quality in the pig barn at least twice a year and to test both at the beginning and at the end of the water lines. Over time, a biofilm will form inside pipes; it is important to treat waterlines with hydrogen peroxide and organic acids to flush out any buildup.

Water is the single most important nutrient, yet sometimes it can be taken for granted. By implementing a program that monitors and maintains proper levels of the five water quality indicators and by carrying out proper equipment maintenance, pig producers will be able to avoid costly problems that can negatively affect the performance of their herd.

Quality norms for water

 
Good
Take action
pH
5.5–8.5
< 4 or > 9
Ammonium (mg/l)
< 1.0
> 2.0
Nitrite (mg/l)
< 0.10
> 1.00
Nitrate (mg/l)
< 100
> 200
Chloride (mg/l)
< 250
> 2,000
Sodium (mg/l)
< 400
> 800
Sulfate (mg/l)
< 150
> 250
Iron (mg/l)
< 0.5
> 10.0
Manganese (mg/l)
< 1.0
> 2.0
Hardness (ppm)
< 60
> 300
Coliforms (cfu/ml)
< 100
> 100
Total bacterial count (cfu/ml)
< 100,000
> 100,000

I want to learn more about nutrition for my pig herd.

Loading...